Wanted info |
Post Reply | Page <123> |
Author | |
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
You don’t get anything thing out if you don’t put the work in.
|
|
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
Turned all the parts and will show pics as I install tomorrow.
|
|
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
Just got finished and Prosport is much better no spring twang as with the old loose spring guide
Turned a nice tight one up in Nylatron as are the piston extension and top hat, a slight radius was required on Seal undercut to allow fitting of the extension also needed 4 slots to allow expanding to fit a good tap with My tapometer so this is a nice tight fit. A bit stringy to turn but pleased with results and new seals now a lot cheaper and easy to change. New breech o’rings aswell. The spring isn’t standard so would like to get one as this one seems a bit strong but Will see how it goes 31coils. Hello I will get some photos on. Shimmed side play in trigger now much better Piston extension 17.5mm Copied what a UK guy did but used existing undercut and didn’t need to use securing screws. https://nbroadsman.me.uk/index.php/air-rifles/air-arms-tx200-hc-tuning Edited by Stuart - 13 Jul 2023 at 8:49pm |
|
Pauly5
Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1394 |
Post Options
Thanks(0)
|
Looking forward to seeing them.
|
|
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
I don’t seem to have permission to load photos
Edited by Stuart - 16 Jul 2023 at 12:15pm |
|
Pauly5
Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1394 |
Post Options
Thanks(0)
|
I had a look and can't see any restrictions on your profile.
Maybe Nunga will check, he knows heaps more about it. I can see you have a couple of images uploaded, but can't see them or when you uploaded them. |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2226 |
Post Options
Thanks(0)
|
Showimg up on my ph.
|
|
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
Yep all good now thanks.
|
|
Pauly5
Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1394 |
Post Options
Thanks(0)
|
There ya go.
I'll be interesting to see how the O ring setup goes for you. Good work! Would a quick blast of heat get rid of the stringy bits? Where did you buy that material from?
|
|
Stuart
Senior Member Joined: 20 Feb 2017 Location: North Canterbur Status: Offline Posts: 136 |
Post Options
Thanks(0)
|
Offcut of 30dia x 150mm Nylatron from LEP Plastics Chch $10
O’rings Pacific seals Wellington total of 6 for piston and breech 2 sets of each for spares total $7 Nylatron specs The closest to Oilon Nylon is Nylatron GSM which is specifically formulated with a molybdenum disulfide (MoS2) additive. This additive provides enhanced strength, rigidity, and self-lubricating properties to the material. The presence of MoS2 particles helps to reduce friction and wear, making Nylatron GSM well-suited for applications involving sliding or rotating parts. Guy in Uk been using his setup for about 3 years with no trouble at all with extension and theViton o’ring So I will have to get out and do some shooting and see how mine goes. Edited by Stuart - 14 Jul 2023 at 12:47pm |
|
Post Reply | Page <123> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |