Laminated blank or plywood

Author

Message

Topic Search

Topic Options

Pauly5

Forum Moderator

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410

Post Options

Post Reply

Quote Pauly5

Report Post

Thanks(0)

Quote

Posted: 13 Jun 2017 at 12:28pm

She's a high tech operation for sure.

Novagun

Groupie

Joined: 13 Dec 2016
Location: Wellington
Status: Offline
Posts: 62

Post Options

Post Reply

Quote Novagun

Report Post

Thanks(0)

Quote

Posted: 13 Jun 2017 at 9:47pm

Pauly5. I had a look at corebox bits to do the inletting of the stock. Biggest I could find was 12.5 mms. I suppose you could get one made but costly. 36 mms is a big bit and would have to be 1/2 inch shank. And need a grunty router and take. a few cuts.

I have used ordinary high carbon steel spade bits and cut the spur off leaving just a rounded peg to act as a guide in a sawcut to the right depth and ground the bit round. It works but the shank is only 6mm so you get a bit of chatter and the finish needs sanding. Gentle light cuts because you don't want to bend the shank at 1000s rpm.

I was not really very happy doing it. Gloves goggles face mask. Safer with a proper 1/2 inch shank bit.

Pauly5

Forum Moderator

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410

Post Options

Post Reply

Quote Pauly5

Report Post

Thanks(0)

Quote

Posted: 13 Jun 2017 at 11:51pm

Yes I remember you telling me that once, but I'm not as brave as you. There is a 35mm core box bit available with 1/2 in shank, and Ryobi have a router that will handle it. The last stock I did I ended up bedding the action, which worked well I thought. This also eliminated the need to get the inlet perfect. I nearly went out and spent the money on impulse, but have decided to just tread carefully, do multiple runs and bed the action.

dvlnme

Senior Member

Joined: 30 May 2017
Location: taranaki
Status: Offline
Posts: 519

Post Options

Post Reply

Quote dvlnme

Report Post

Thanks(0)

Quote

Posted: 18 Jun 2017 at 9:15am

Been thinking bout this one for while,made lot stocks over the years,some using laminated walnut and other woods etc,allso made couple using ply,most proper laminated blanks ore made in thin layers the opposite way to ply,you can get same effect by stacking ply n gluing,get same effect as proper laminated

stock blanks,looks nicer than ply,but bit mor trouble to make up blank,tho i think end result worth it

Cheers Mike

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1410	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 13 Jun 2017 at 12:28pm
	She's a high tech operation for sure.

Novagun Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 13 Dec 2016 Location: Wellington Status: Offline Posts: 62	Post Options Post Reply Quote Novagun Report Post Thanks(0) Quote Reply Posted: 13 Jun 2017 at 9:47pm
	Pauly5. I had a look at corebox bits to do the inletting of the stock. Biggest I could find was 12.5 mms. I suppose you could get one made but costly. 36 mms is a big bit and would have to be 1/2 inch shank. And need a grunty router and take. a few cuts. I have used ordinary high carbon steel spade bits and cut the spur off leaving just a rounded peg to act as a guide in a sawcut to the right depth and ground the bit round. It works but the shank is only 6mm so you get a bit of chatter and the finish needs sanding. Gentle light cuts because you don't want to bend the shank at 1000s rpm. I was not really very happy doing it. Gloves goggles face mask. Safer with a proper 1/2 inch shank bit.

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1410	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 13 Jun 2017 at 11:51pm
	Yes I remember you telling me that once, but I'm not as brave as you. There is a 35mm core box bit available with 1/2 in shank, and Ryobi have a router that will handle it. The last stock I did I ended up bedding the action, which worked well I thought. This also eliminated the need to get the inlet perfect. I nearly went out and spent the money on impulse, but have decided to just tread carefully, do multiple runs and bed the action.

dvlnme Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 30 May 2017 Location: taranaki Status: Offline Posts: 519	Post Options Post Reply Quote dvlnme Report Post Thanks(0) Quote Reply Posted: 18 Jun 2017 at 9:15am
	Been thinking bout this one for while,made lot stocks over the years,some using laminated walnut and other woods etc,allso made couple using ply,most proper laminated blanks ore made in thin layers the opposite way to ply,you can get same effect by stacking ply n gluing,get same effect as proper laminated stock blanks,looks nicer than ply,but bit mor trouble to make up blank,tho i think end result worth it Cheers Mike