Down the rabbit hole |
Post Reply | Page <1234 9> |
Author | |
CuteRabbit
Senior Member Joined: 17 Jan 2023 Location: Albany Auckland Status: Offline Posts: 120 |
Post Options
Thanks(0)
|
I filled my sandbag with newspaper, which is too light... Also the table is too low that I can merely put my cheek on to the stock...
|
|
Squirrel goes Vege
@Crosman Benjamin Ironhide .22 Nitro Piston Elite @Umarex Surgemax .177 Gas Ram 1000fps |
|
CuteRabbit
Senior Member Joined: 17 Jan 2023 Location: Albany Auckland Status: Offline Posts: 120 |
Post Options
Thanks(0)
|
I think I didn't make it clearly, this pic is what i say
|
|
Squirrel goes Vege
@Crosman Benjamin Ironhide .22 Nitro Piston Elite @Umarex Surgemax .177 Gas Ram 1000fps |
|
CuteRabbit
Senior Member Joined: 17 Jan 2023 Location: Albany Auckland Status: Offline Posts: 120 |
Post Options
Thanks(0)
|
thanks,gonna visit guncity someday recently I think
|
|
Squirrel goes Vege
@Crosman Benjamin Ironhide .22 Nitro Piston Elite @Umarex Surgemax .177 Gas Ram 1000fps |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Online Posts: 1705 |
Post Options
Thanks(0)
|
I use a string line with a heavy weight which I line the vertical cross hair up with, and a string line bubble level on the rifle on a flat machined face(usually one on top of rifle somewhere) for setting scope.
Have used the edge of builders level instead of string line. Though what you suggest is a way more practical solution, and can be used to make sure you arnt canting rifle when shooting. |
|
FPM
Groupie Joined: 31 Dec 2022 Location: New Zealand Status: Offline Posts: 56 |
Post Options
Thanks(0)
|
I bought a new BSA scope recently which was factory fitted on its rail mount. But I thought I would check it with my Accutech level and sure enough it was off. I suggest you consider this if you don't already have one: https://www.guncity.com/accutech-reticle-level-kit-379898 I don't bother with a cleaning set. Just Rem Oil and paper towels. If your rifle has a factory fitted and fixed moderator like the Gamo and BSA, then bore cleaning is a risky proposition. Personally, I don't bother. Its not like there is combustion as in a powder rifle. I have a safe dehumidifier which I pull out every week or so and plug in overnight. Definitely an item worth having if your rifles are stored in an enclosed location like a safe (as they should be).
Edited by FPM - 05 Feb 2023 at 1:34am |
|
CuteRabbit
Senior Member Joined: 17 Jan 2023 Location: Albany Auckland Status: Offline Posts: 120 |
Post Options
Thanks(0)
|
Thanks. Doing a lot adjustment and finally find out that the scope is leaning toward right becasue the srews on each mount side are not equally tightened... So the former sight-in work won't fix this problem totally. Re do it and will try flat nose and round nose tomorrow if not rainning.
Flat nose- guncity Round nose- Winchester (made in Spain so is good?) Will try: rest-sandbag normoal standing an alternative pose of artillery hold (fold left arm, use the elbow to hold the gun, left hand grabing right wrist rather than use left hand to hold it)
Edited by CuteRabbit - 04 Feb 2023 at 5:17pm |
|
Squirrel goes Vege
@Crosman Benjamin Ironhide .22 Nitro Piston Elite @Umarex Surgemax .177 Gas Ram 1000fps |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Online Posts: 1705 |
Post Options
Thanks(0)
|
Paper tear may also be the target not held firm against the backing board.
Looks like from top pic that it's only held on by couple of pegs and is paper. |
|
Billbobnz
Senior Member Joined: 13 Jun 2020 Location: Ashburton Status: Offline Posts: 779 |
Post Options
Thanks(0)
|
Buy a H&N sample pack of pellets. And see high quality flat nose (go to young's air guns on dominion road for these)
|
|
Billbobnz
Senior Member Joined: 13 Jun 2020 Location: Ashburton Status: Offline Posts: 779 |
Post Options
Thanks(0)
|
This is how to read your shots
Blue is your group, red are what we call fliers (generally caused by a damaged pellet) or a poor shot or form. The purple arrows point to the paper tear I was talking about earlier and most likely caused by a off balance pellet. Generally with myself. If I do a poor shot it's because I've flinched or closed my eyes when I've taken the shot. Edited by Billbobnz - 04 Feb 2023 at 1:25pm |
|
Billbobnz
Senior Member Joined: 13 Jun 2020 Location: Ashburton Status: Offline Posts: 779 |
Post Options
Thanks(0)
|
Cuterabbit, you should try a few different pellets.
Get flat nose (which I think you already have) and domed/diablo pellets. Looking at the target you have shot and looking at the paper tears the pellets may be tumbling or spiralling when they hit. Therefore there isn't a clean punch through the paper. (Others may be able to comment on this) Once you have a selection of pellets. Do 5 shot of each pellet on their own target and look for grouping and how clean the holes. |
|
Post Reply | Page <1234 9> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |