Kiwi Airgunners Homepage
Forum Home Forum Home > General > Flub's General Discussion
  New Posts New Posts RSS Feed - CR600w Mods
  FAQ FAQ  Forum Search   Register Register  Login Login

CR600w Mods
 Post Reply Post Reply Page  <123
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Elliot87 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 19 Feb 2023
Location: Christchurch
Status: Offline
Posts: 100 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Elliot87 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Mar 2023 at 9:19pm
Originally posted by Pauly5 Pauly5 wrote:

I have used a wooden dowel that I shaped to fit, then used sandpaper wrapped around it. If there are any obvious burrs, target them, then smooth it all off. Check the transfer port as well to make sure there aren't burrs there too.

That sounds like a good way to do it. I'm assuming a course to medium grid sandpaper would be ok?
Pom that wants to be a kiwi
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 13 Jun 2020
Location: Ashburton
Status: Offline
Posts: 867 		Post Options Post Options   Thanks (1) Thanks(1)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 14 Mar 2023 at 9:28pm
22cal bronze barrel brush could work too
Back to Top
Elliot87 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 19 Feb 2023
Location: Christchurch
Status: Offline
Posts: 100 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Elliot87 Quote  Post ReplyReply Direct Link To This Post Posted: 14 Mar 2023 at 9:36pm
Is there a reason these refillable 12g co2 capsules http://www.ebay.com/itm/124618547296 couldn't be extended with a piece of threaded tubing in the middle, so they fit the space where 3 normal 12g co2 capsules go?

It would be great to have a couple of ~36g bulk filled co2 containers that could be used without making any modifications to the rifle.  I think this is essentially what dvlnme said he has made in a different thread but I'm not exactly sure how he made his.

I'm assuming there is a reason why this isn't something everyone is doing, as on the surface it seems like a great solution.
One thing I'm unsure about is if you could simply drop one of the refillable capsules into the gun and have it work without making any changes to it?


Edited by Elliot87 - 14 Mar 2023 at 9:37pm
Pom that wants to be a kiwi
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 15 Mar 2023 at 7:36am
Originally posted by Elliot87 Elliot87 wrote:

Originally posted by Pauly5 Pauly5 wrote:

I have used a wooden dowel that I shaped to fit, then used sandpaper wrapped around it. If there are any obvious burrs, target them, then smooth it all off. Check the transfer port as well to make sure there aren't burrs there too.


That sounds like a good way to do it. I'm assuming a course to medium grid sandpaper would be ok?



I wouldn't go any more coarser than 400 grit, then I would finish with a higher grit so it's nice and polished for the pellet to travel over. You could even get autosol and using the wood dowel, polish it. The dowel should mold to the harder surface. Making sure to remove all traces of autosol from the barrel afterwards too.
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 13 Jun 2020
Location: Ashburton
Status: Offline
Posts: 867 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 16 Mar 2023 at 10:59pm
Those refillable canisters I'm sure you could extend. dvlnme will know best on this idea.
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 17 Mar 2023 at 11:51am
I'm sure we will hear from Dvlnme soon. He has had an eye injury and been unable to look at screens for a while.
Back to Top
Elliot87 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 19 Feb 2023
Location: Christchurch
Status: Offline
Posts: 100 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Elliot87 Quote  Post ReplyReply Direct Link To This Post Posted: 17 Mar 2023 at 5:23pm
Originally posted by Pauly5 Pauly5 wrote:

I'm sure we will hear from Dvlnme soon. He has had an eye injury and been unable to look at screens for a while.

I had seen that he hadn't been active on here for a few months and before I joined, so I didn't want to message him out of the blue about it.
Pom that wants to be a kiwi
Back to Top
 Post Reply Post Reply Page  <123
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.059 seconds.