CRC Molygraph grease

Author

Message

Topic Search

Topic Options

Daz-nz

Groupie

Joined: 23 Dec 2025
Location: Wanganui
Status: Offline
Posts: 18

Post Options

Post Reply

Quote Daz-nz

Report Post

Thanks(0)

Quote

Topic: CRC Molygraph grease
Posted: 13 Feb 2026 at 5:48am

CRC Molygraph grease

Has anyone used this product?
Just ordered a tube to try

https://www.crcindustries.com/moly-graph-extreme-pressure-multi-purpose-lithium-grease/

Trademe listing 5781006905

jwabfrog

Senior Member

Joined: 13 Nov 2021
Location: Thames
Status: Offline
Posts: 162

Post Options

Post Reply

Quote jwabfrog

Report Post

Thanks(0)

Quote

Posted: 13 Feb 2026 at 7:28am

It will work fine on a spring etc. Most greases claiming moly content have very little molybdenum disulfide in them. True moly greases e.g. Molybod GA50 are super pricey but a little goes a long way. You can use a lot less to get the lubricating effect.

If you're greasing a springer be careful not to get any forward of the piston seal as it will detonate! Tinbum tuning recommends using very little grease, other tuners use more including 'heavy tar' as it has a dampening effect and makes a springer feel less harsh.

-Ec

Senior Member

Joined: 02 Sep 2025
Location: Matamau
Status: Offline
Posts: 128

Post Options

Post Reply

Quote -Ec

Report Post

Thanks(0)

Quote

Posted: 2 hours 30 minutes ago at 8:30pm

I used a small amount of a similar product on the spring of my Webley Mark 1 pistol when I rebuilt it.

I got some Rocol dry moly paste a while back on Trademe which I used on the piston. 100g tube cost approx $80 from memory but that will out last me.

Did have a quick search on Trademe but this was no longer listed.

did find this which seems a bit pricey - though if you are maintaining a few guns is cost effective as you only need a tiny amount.

https://www.trademe.co.nz/a/motors/car-parts-accessories/other-accessories/listing/5783774147

Also found this.

https://www.trademe.co.nz/a/motors/car-parts-accessories/oil-additives/listing/5775479087

Even though it is called Liqui Moly, the info about the product say is contains tungsten disulphide. However looking into this indicates that this might be a better product - see below for more info.

https://ws2coating.com/a-comparison-of-tungsten-disulfide-and-molybdenum-disulfide/

Edited by -Ec - 2 hours 28 minutes ago at 8:32pm

Regards
-Ec

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Daz-nz Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 23 Dec 2025 Location: Wanganui Status: Offline Posts: 18	Post Options Post Reply Quote Daz-nz Report Post Thanks(0) Quote Reply Topic: CRC Molygraph grease Posted: 13 Feb 2026 at 5:48am
	CRC Molygraph grease Has anyone used this product? Just ordered a tube to try https://www.crcindustries.com/moly-graph-extreme-pressure-multi-purpose-lithium-grease/ Trademe listing 5781006905

jwabfrog Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 13 Nov 2021 Location: Thames Status: Offline Posts: 162	Post Options Post Reply Quote jwabfrog Report Post Thanks(0) Quote Reply Posted: 13 Feb 2026 at 7:28am
	It will work fine on a spring etc. Most greases claiming moly content have very little molybdenum disulfide in them. True moly greases e.g. Molybod GA50 are super pricey but a little goes a long way. You can use a lot less to get the lubricating effect. If you're greasing a springer be careful not to get any forward of the piston seal as it will detonate! Tinbum tuning recommends using very little grease, other tuners use more including 'heavy tar' as it has a dampening effect and makes a springer feel less harsh.

-Ec Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 02 Sep 2025 Location: Matamau Status: Offline Posts: 128	Post Options Post Reply Quote -Ec Report Post Thanks(0) Quote Reply Posted: 2 hours 30 minutes ago at 8:30pm
	I used a small amount of a similar product on the spring of my Webley Mark 1 pistol when I rebuilt it. I got some Rocol dry moly paste a while back on Trademe which I used on the piston. 100g tube cost approx $80 from memory but that will out last me. Did have a quick search on Trademe but this was no longer listed. did find this which seems a bit pricey - though if you are maintaining a few guns is cost effective as you only need a tiny amount. https://www.trademe.co.nz/a/motors/car-parts-accessories/other-accessories/listing/5783774147 Also found this. https://www.trademe.co.nz/a/motors/car-parts-accessories/oil-additives/listing/5775479087 Even though it is called Liqui Moly, the info about the product say is contains tungsten disulphide. However looking into this indicates that this might be a better product - see below for more info. https://ws2coating.com/a-comparison-of-tungsten-disulfide-and-molybdenum-disulfide/ Edited by -Ec - 2 hours 28 minutes ago at 8:32pm
	Regards -Ec