|
Valve mod - pcp pistol |
Post Reply 
|
Page <1234 5> |
| Author | |
nunga 
Forum Moderator 
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1012 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 04 Sep 2024 at 11:33am |
|
I would highly recommend the bronze alloy as you have to take into account for bimetallic corrosion if you were to use a screwdriver shaft with a stainless steel seat. it would rust out very quickly or weld itself together. be very careful when mixing your ferrous metals
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
 |
|
|
Pauly5
Forum Moderator
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1415 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2024 at 12:02pm |
|
Cool, great info.
In the past, I have used delrin on the shaft which has worked well, but I was thinking of keeping the HP side of the valve stem to a minimum using metal which means the metal head can be made smaller and more streamlined. I quote some advice given below. "Therefore you can reduce both major closing forces on the valve:" 1) reducing the static pressure on the valve stem 2) reducing the dynamic pressure on the valve head
|
|
|
|
|
RangerPete
Senior Member 
Joined: 18 Apr 2023 Location: Cambridge. Status: Offline Posts: 884 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2024 at 12:05pm |
|
Interesting thread Pauly.
Is this going to be another crossman modification? And what caliber are you using? |
|
|
Walk quietly, but carry a big stick.
|
|
|
|
|
Pauly5
Forum Moderator
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1415 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Sep 2024 at 12:23pm |
I am trying to make as much as I can, but will use a Crosman trigger frame and barrel. I have a steel breech which will save a lot of time, but would like to make a custom breech with a straight pull bolt that has a locking action rather than drop into a slot. very similar to my last build. That way I could get a little creative with open sights maybe. It'll be .22. I do have a .25 cal FX barrel off an old Bobcat, but of course it'll need chopping down, but had thought about using that for a rifle build.
|
|
|
|
|
xyon
Senior Member
Joined: 20 Dec 2016 Location: Canterbury Status: Offline Posts: 135 |
Post Options
Thanks(1)
Quote Reply
Posted: 04 Sep 2024 at 12:42pm |
Hi, I don't think 316 would be hard enough for the valve stem/shaft, well that would depend of course on how hard you need to hit it and the diameter. FX valve stems (among others) have been known break  |
|
|
---
My favourites springer - Diana 52 PCP - FX Wildcat III |
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1012 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2024 at 11:35am |
|
Paul Flick me your address and ill get that bronze sent to you. I will be doing a smelt over the weekend and i will make some bronze while i have the furnace cranked up
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
BC_Clark
Member 
Joined: 15 Feb 2024 Location: Auckland Status: Offline Posts: 6 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2024 at 5:20pm |
|
A thing about dissimilar metal corrosion is it depends on the ratio of surface areas of each metal. A stainless seat in an aluminium airgun could have no issues but an aluminium seat in a stainless airgun would be at high risk. Look up the galvanic series and make sure that the most reactive metal makes up the vast majority. I find 385 brass to be very good for seats. It machines and polishes well. Bronzes can be more tricky. |
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1012 |
Post Options
Thanks(1)
Quote Reply
Posted: 06 Sep 2024 at 5:49pm |
|
Thats because 385 brass as a lot of lead (around 3%) compared with other types of brass which makes it very good for machining it is also know as free machining brass. But it is a lot softer as well so i dont know how it would handle been used on HPA valve seat. If you have had good results using it BC_Clark then i would be happy to mix up a batch for you paul, like i said i have everything here and i will be smelting other stuff this weekend anyway.
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
BC_Clark
Member
Joined: 15 Feb 2024 Location: Auckland Status: Offline Posts: 6 |
Post Options
Thanks(1)
Quote Reply
Posted: 07 Sep 2024 at 7:50pm |
Some of my most powerful and highly stressed valves have been with 385 brass seats so I can say that normal HPA usage is no challenge. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1415 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2024 at 8:26pm |
|
So should I remake that valve seat in brass and the harder material for the moving part of the valve. Poppet valve?
|
|
|
|
|
Post Reply
|
Page <1234 5> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
RangerPete wrote: