|
Laminate stock Series II |
Post Reply 
|
Page <123> |
| Author | |
Davey 
Groupie 
Joined: 10 May 2014 Location: In the Office Status: Offline Posts: 80 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 28 Jun 2014 at 2:59am |
|
The only thing about these stock blanks, is I feel they all shoulder too low on the rifle for the seated position. When your shoulder is in line with the bore you get the least recoil.
I guess you can just move the buttplates up.
|
|
 |
|
|
(pink)MIST
Forum Moderator 
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jun 2014 at 2:19am |
|
I oiled and let it dry overnight, sand and repeat etc
|
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
Davey
Groupie
Joined: 10 May 2014 Location: In the Office Status: Offline Posts: 80 |
Post Options
Thanks(0)
Quote Reply
Posted: 28 Jun 2014 at 2:11am |
|
Looks purty. Can't wait to see it in action!
|
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jun 2014 at 4:47pm |
|
Did you sand it with the finish oil or did you use water? I tried a bit of the oil and it dried up while sanding. I haven't done a wet and dry sand yet. How say you?
Edited by Pauly5 - 27 Jun 2014 at 5:06pm |
|
|
|
|
(pink)MIST
Forum Moderator
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jun 2014 at 4:34pm |
|
I got quite happy with the finish when I got to 8coats on mine , and 600grit wet n dry paper. Almost looked lacquered :)
Looking nice pauly5, can't wait to see it in the line :) |
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jun 2014 at 4:22pm |
|
I put a couple of coats of tru oil on it now. Sanding between coats with fine grit. It makes the layers stand out nicely. It has a warmth to it. It's not perfect but really pleased with it. I can't wait to get it all finished and use it more.
 
|
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2014 at 3:34pm |
|
Good. It's a bit heavier but position wise seems really good. I will need a hook as it's heavier up front.
|
|
|
|
|
(pink)MIST
Forum Moderator
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2014 at 2:09pm |
|
Can't hurt, I've found star washers work quite well.
POI shift could be bolts done up tighter than before, or slightly off center and pulling the action differently. As long as they're all hitting the same spot tho, not spraying a shotgun pattern of lead everywhere , then once re zeroed it should be game on as normal |
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 Jun 2014 at 1:44pm |
|
I put a few shots through it today and it hit the same spot but poi was higher. I plan to bed the action. Just wondering if I will need to re zero once settled into this stock. I guess fire it heaps and keep screws tight so the stock settles in. Should I epoxy around the bolt holes to strengthen them?
|
|
|
|
|
(pink)MIST
Forum Moderator
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jun 2014 at 3:22pm |
|
Oil on laminate will definitely give you contrast :)
Ooooo it's getting close now :) |
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jun 2014 at 12:33pm |
|
Not really. I had tested a bit of Tru oil on an off cut and liked that. I like the idea of using an oil I can wet sand with as it gives that baby bum smoothness with out too much gloss. I had used tru oil on an oak stock once and really liked that, plus I have some left over. So I don't really want to stain it anymore than slightly darken the layers for the contrast.
|
|
|
|
|
(pink)MIST
Forum Moderator
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jun 2014 at 12:18pm |
|
Have you decided on what finish you're going to apply to it?
If you're going to stain it don't use an NGR type stain, as it will hide the laminate lines. Also, try your finish on a bit of scrap first if you can, gives you the option of using an oil, but feeding colour into the oil first :) |
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 11 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1676 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Jun 2014 at 11:24am |
|
I spent a couple of hours fitting the action and drilling holes. I haven't drilled the stock screw holes in the photo yet but they're done. I fired a couple of shots and the stock absorbs more recoil which is good. I also fitted my revolutionary butt hook. It's a totally different feeling gun, can't wait to actually use it. The cheek rest is about right as it is but actually need to lower it a bit so I don't think I will make it adjustable yet as I may not need to.
  Edited by Pauly5 - 24 Jun 2014 at 11:31am |
|
|
|
|
(pink)MIST
Forum Moderator
Joined: 10 Mar 2013 Location: Hamilton Status: Offline Posts: 465 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 Jun 2014 at 3:06am |
|
Two thumbs up :)
That's gonna be pretty special to look at once it's got a finish applied :) |
|
|
NZAFTA President
1st place HP springer - 2014 WFTF Worlds 1st place HP springer - 2014 Nats AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design. |
|
|
|
|
nunga
Admin 
Joined: 09 Mar 2013 Location: Pukekohe Status: Offline Posts: 1083 |
Post Options
Thanks(0)
Quote Reply
Posted: 21 Jun 2014 at 3:02am |
|
looking real good mate
|
|
|
|
|
Post Reply
|
Page <123> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options