Rekord trigger mod

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   Ended up doing the set screw thing again. worked well. It's lightened the trigger a tad, but still good safe sear engagement.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Topic: Rekord trigger mod Posted: 24 Jul 2017 at 11:27pm
	Ended up doing the set screw thing again. worked well. It's lightened the trigger a tad, but still good safe sear engagement.

nunga Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Forum Moderator Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1009	Post Options Post Reply Quote nunga Report Post Thanks(0) Quote Reply Posted: 24 Jul 2017 at 9:55am
	I would just use a small ball bearing its already hardened and nice and smooth. or go to your local engineering shop and have a look at what hardened pings they have.
	2nd place HP springer - WFTF World Championships 2014

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 22 Jul 2017 at 10:35am
	Well I'm back making another trigger. I made a new stock, and want to set the trigger back. I may or may not have measured something wrong when inletting, but that's another story. In the trigger blade I made above I used set screws with polished ends, this time i want to use a roller for where the blade contacts with the sear arm. My questions is, I would need to use hardened steel correct? Where do I get a bit of rod approx 3 mm? Drill bit, section of spring, shaft of a small screw driver? Will heating and quenching be good enough for my purpose? I know this will only work for high carbon steel, so are any of those things high carbon? And how would I cut and smooth it if it is hardened, or do I do all that before hardening it? Lots of questions for you engineer minded gunners. Thanks in advance.

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 14 Oct 2015 at 10:42pm
	I installed the trigger unit back into the 95 today. After a few shots it is feeling good I must say. It's not fantastically different, but it feels softer and lighter, plus the different shaped trigger being a bit closer to the grip feels better. (short fingeritis) Not that the Rekord ever felt bad, but I think I like the change. So I will just shoot it for a while before I go changing the position of the trigger axle forward. The let off just goes now, where before there was a slight resistance, then a crisp release, so I must have changed the geometry enough to safely lighten it. To test it, I loaded the gun, took safety off and struck the butt with a rubber mallet a few times and it never went off, so I'm happy. You can see the two adjustment screw holes, 1st and second stage easily accessible while fitted. I will take it out and polish it up after I've shot some stuff with it. And that's it. If I made one that is set back anymore I would have to change the trigger weight screw out for a shorter one.

nunga Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Forum Moderator Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1009	Post Options Post Reply Quote nunga Report Post Thanks(0) Quote Reply Posted: 10 Oct 2015 at 9:47am
	make sure you do drill the hole forward and not back or you will end up increasing the trigger pull weight :)
	2nd place HP springer - WFTF World Championships 2014

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 10 Oct 2015 at 12:12am
	Next thing I might do is to move the trigger forward by drilling a new hole in the case. Other forums say 6 mm. See how I go later.

nunga Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Forum Moderator Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1009	Post Options Post Reply Quote nunga Report Post Thanks(0) Quote Reply Posted: 09 Oct 2015 at 11:18pm
	Nice work mate :)
	2nd place HP springer - WFTF World Championships 2014

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 09 Oct 2015 at 10:36pm
	Ok, take 2. I now have an adjustable, functioning 2 stage trigger. I think I had drilled the holes too small and the tap was gripping too much in the hole. With these ones I made the hole 2.5 mm instead of 2 mm. There was still some movement when the set screw is in place.so I gave the side a tap with the hole punch tightening up the screw. Set screws were 3 mm. What I like about this rekord trigger is that you can test it without being installed in the gun. The let off feels very light at this stage, but who knows, I could have spent all that time accomplishing nothing Don't look too close at the workmanship. Macro on the camera doesn't help. The blade is still too long to fit in the guard so the next thing is to cut it off, then tidy it up as much as possible. I will polish the sears then refit the unit for field testing.

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 03 Oct 2015 at 11:05pm
	Ok, so all going well at this stage. I decided to use the bearings with a flange as they took up play in the trigger housing. 6 mm aluminium + 2 x .5 mm flanges = 7 mm. Perfect fit. Drill the first stage hole. Then drilled the second. I tapped the thread for the first stage. Then I started tapping the second and the tap broke. Here's a shot of the trigger as it sits now. It works but One stage only. I will start another tomorrow.

Pauly5 Members Profile Send Private Message Find Members Posts Add to Buddy List Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411	Post Options Post Reply Quote Pauly5 Report Post Thanks(0) Quote Reply Posted: 03 Oct 2015 at 9:21pm
	Disaster! So close though. I got the first stage in and as I was tapping the second the bloody tap broke in the hole. I guess I was getting excited and not patient enough. But it worked, even with just the first stage. Will post pictures to disaster stage later, then start on the next one.