|
Sash clamps. |
Post Reply 
|
Page 12> |
| Author | |
J-S 
Senior Member 
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
 Post Options
 Thanks(0)
 Quote Reply
 Topic: Sash clamps.Posted: 05 Nov 2024 at 9:37am |
cheers, worked ok for the oversprung gamo.. though you had to break the barrel to slip it through then straighten it out to compress - wouldnt work with a fixed barrel - youd need to make a removable clamping piece... easier to grab a sash clamp!
|
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
 |
|
|
jwabfrog
Senior Member
Joined: 12 Nov 2021 Location: Thames Status: Offline Posts: 142 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Nov 2024 at 8:52am |
|
Nice setup JS, barrel poking through the hole is a good way to make a shorter clamp work
|
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Nov 2024 at 8:28am |
 G clamp is off to the right.. it was a knock up job, if I had more time I’d make the barrel stop adjustable and a block to clamp the cylinder down |
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 05 Nov 2024 at 8:23am |
|
I made a jig up a couple years back; wood base with half a G clamp bolted to it. Wood piece at the end to with a hole to hold the barrel in place and a wood piece along the side for the cylinder. Worked well for the gun I was doing..
|
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
RangerPete
Senior Member
Joined: 18 Apr 2023 Location: Cambridge. Status: Offline Posts: 884 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2024 at 9:08am |
|
Thanks for the replys guys.
I've also found a 1200mm big metal, screw type sash clamp at miter 10, so I guess thats going to be the one 
|
|
|
Walk quietly, but carry a big stick.
|
|
|
|
|
jwabfrog
Senior Member
Joined: 12 Nov 2021 Location: Thames Status: Offline Posts: 142 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2024 at 8:59am |
|
My five cents is go for a longer clamp around 1200mm with a screw. The screw allows you to make fine adjustments to add or remove compression. With a quick release it releases compression all in on go. A compressed spring has a fair amount of pre compression travel which can release violently and fire parts into dark corners of your garage..... 1200mm length will allow you to hold the barrel + action between the clamps.
Like Pauly said, a means of holding the rifle and stopping it from sliding out of the clamp when it's under compression is a good idea.
|
|
|
|
|
Pauly5
Forum Moderator 
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1410 |
Post Options
Thanks(0)
Quote Reply
Posted: 04 Nov 2024 at 7:41am |
|
If there isn't much preload, you can sometimes open up without a clamp. But when I opened up my first 97 it had a long soft spring in it and there was about 80 mm of preload, so I needed the travel on a sash clamp to release the pressure or else I would have injured myself.
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 Nov 2024 at 8:38pm |
|
I use a Irwin quick grip.
Place a bit of wood on it to protect the spring. Takes up most of the slack and has a stopping pin at end of bar. Travels a couple of inches till it hits it. Not that much pressure or travel on an uncocked spring. |
|
|
|
|
Pauly5
Forum Moderator
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1410 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 Nov 2024 at 5:46pm |
|
I use a sash clamp.
Or the DIY one is quite do able. It's a good idea to be able to hold the gun as well so it doesn't slip off to the side.
|
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1009 |
Post Options
Thanks(0)
Quote Reply
Posted: 03 Nov 2024 at 4:37pm |
|
Well the quick release ones will not be any use to you because the release very quickly. They good for compressing the spring or gas piston. I just used some timber. drill a hole in it and get some m12 threaded bar with some nuts and a couple of washers and you are good to go. way cheaper
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
Post Reply
|
Page 12> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
jwabfrog wrote: