|
Salvaging Damaged Pellets |
Post Reply 
|
Page <12 |
| Author | |
KiwiTR6 
Senior Member 
Joined: 03 Nov 2022 Location: Stratford Status: Online Posts: 282 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 21 Nov 2024 at 9:06pm |
|
Thanks Kruza, it'll be a lot of fun regardless of the results  I might grab that off you Mark, it's not much good for anything else so I wouldn't feel bad about taking a welder to it.... |
|
|
FX Wildcat MK111 BT Sniper .25
FX Dreamline Classic .22 Diana Outlaw .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 PCP Custom .22 Crosman 2250 PCP Custom .22 Brocock Grand Prix .22 |
|
 |
|
|
JasonEdward
Senior Member
Joined: 21 Sep 2024 Location: Waihi Status: Offline Posts: 95 |
Post Options
Thanks(0)
Quote Reply
Posted: Yesterday at 12:05pm |
|
Great thread with some rare data re damaged pellets.
Best of luck with the shooting comp and I'll look forward to more testing of damaged pellets re POI... thank you for your efforts! |
|
|
|
|
Pauly5
Forum Moderator 
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1410 |
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 32 minutes ago at 9:28am |
|
Yea, a good thread.
That first shot from a mag is defnitely the one to watch too.
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 5 hours 22 minutes ago at 9:38am |
|
Am I right in assuming that the first round in a mag is the one that locks the mag to loaded and takes the full weight of the spring that turns the mag or is that the last pellet fired?
|
|
|
|
|
JasonEdward
Senior Member
Joined: 21 Sep 2024 Location: Waihi Status: Offline Posts: 95 |
Post Options
Thanks(0)
Quote Reply
Posted: 2 hours 18 minutes ago at 12:42pm |
|
Interesting - so can I just clarify that I haven't misunderstood:
Is it that when I fit a magazine into my PCP, press the pin forward to center the rotating mag on it's spindle, this does not actually properly line up the mag so the pellets will slip directly forward into the breech? And that alignment only happens as the first pellet is pushed into the breech and the alignment is done by the actual pellet as it goes into the breech from a non-aligned position? So the first pellet can be subject to deforming as it enters the breech while it is also moving the magazine into proper alignment? And most (or all?) magazine fed air rifles are designed this way? Which is why serious target shooters want feed in single pellets not use magazines? Thanks for educating me :-)
|
|
|
|
|
KiwiTR6
Senior Member
Joined: 03 Nov 2022 Location: Stratford Status: Online Posts: 282 |
Post Options
Thanks(0)
Quote Reply
Posted: 15 minutes ago at 2:38pm |
Yes, that's my theory and explains why for target shooting (as opposed to hunting) many use a single shot feed from a tray which is what I'm now doing with all of my target guns. I recently noticed when target shooting that when I and fellow competitors changed to a new mag the first shot would inevitably be a flyer. Most of my magazines are CARM 3D printed items (beautifully made), but like most 3D printed mags takes a little bit of 'fiddling' to get into place and I believe that the first shot finalises the alignment but in the process potentially scores the side of that first pellet. In an extreme case where the mag isn't correctly manufactured then it's possible that every pellet will be marked which will obviously affect it's performance. Just like a misaligned suppressor that clips pellets it's not obvious unless you have experienced it before. This is not really an issue for hunting, but definitely for target shooting (in my humble opinion). Also, as Kruza mentions, if the return spring for the pellet drum is too tight then the pellet can be damaged as the probe is withdrawn and the next pellet is slammed into place. On the other hand, if the spring is too weak, there is a risk that the drum won't rotate to the next pellet. I imagine a similar problem can occur with a mechanically rotated drum. If the drum doesn't rotate precisely then damage can occur which I now suspect was the problem with my Hunting Master AR6 rifle. Edited by KiwiTR6 - 13 minutes ago at 2:40pm |
|
|
FX Wildcat MK111 BT Sniper .25
FX Dreamline Classic .22 Diana Outlaw .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 PCP Custom .22 Crosman 2250 PCP Custom .22 Brocock Grand Prix .22 |
|
|
|
|
Post Reply
|
Page <12 |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
JasonEdward wrote: