Print Page | Close Window

Swaging

Printed From: Kiwi Airgunners
Category: General
Forum Name: Flub's General Discussion
Forum Description: General discussion goes in here.
URL: www.kiwiairgunners.co.nz/forum_posts.asp?TID=632
Printed Date: 24 Nov 2024 at 1:12am
Software Version: Web Wiz Forums 10.14 - http://www.webwizforums.com


Topic: Swaging
Posted By: delta_mike
Subject: Swaging
Date Posted: 10 May 2022 at 9:12pm
Looking at getting into this to start making my own slugs. Amazed that presses and dies for this cost more than my Dillon 750! Anyway, are any of you making your own slugs? Trying to track down a source of lead wire before heading down this route.

Why swaging? I'm looking to make my own 40 grainers :)


-------------
FX Impact MK3 .22 700mm


Replies:
Posted By: Myson
Date Posted: 11 May 2022 at 8:38am
There's a chap called "SPYDA" making slugs down in the South Island.

Apparently they're great - a mate is currently trialing them in his FX Wildcat Mk3 .22 (with a special Huma Regulator fitted) and he's impressed!

You might like to talk with Spyda....


-------------
https://www.youtube.com/watch?v=eq7jVyBfFqE" rel="nofollow - https://www.youtube.com/watch?v=eq7jVyBfFqE
Air Arms S510 US .22
Air Arms S410 .22
Weihrauch HW97KT .177
Weihrauch HW95 .177

Posted By: xyon
Date Posted: 11 May 2022 at 11:39am
I tried making my own, they looked the part, but were not quite as accurate as the commercial ones. I think I just don't have to tooling to make a die accurately enough, also my press might not have been precise enough either.

I've visited Brian and bought some slugs from him. They were about as accurate as the H&N ones in my wildcat mk III. That is pretty good. The only downside is the hollowpoint is quite small, and I was getting more pass-throughs. NSA and Javelin have good expansion.


-------------
---
My favourites
springer - Diana 52
PCP - FX Wildcat III

Posted By: delta_mike
Date Posted: 11 May 2022 at 5:03pm
Nice, I saw his listings on Trademe. I'll reach out when he lists again.

Looking at the unit from GMI engineering - the "freedom press". You can customise the dies like Corbin.

Disappointed that the NZ dealer for the Javelin slugs have stopped stocking them, those have been my go to.


-------------
FX Impact MK3 .22 700mm

Posted By: dvlnme
Date Posted: 14 May 2022 at 9:41am
i have large number of well used bullet swaging dies here that will fit your dillon press,you may be able to find something among them to suit your needs .pm me and will give you my contact number,i used to be a commercial bullet maker many years ago,and made hundreds thousands swaged lead pistol bullets,swaging dies for lead are a specialised die that bleeds off excess lead,making wire not that hard if know how,i may be able help you set up.
 cheers mike

Posted By: delta_mike
Date Posted: 17 May 2022 at 7:49pm
Thanks Mike, appreciate the offer!

I went with the GMI press/dies in the end. Also found some wire for swaging through DLM Wallace up in Auckland. $10 per kg and diameter to suit.



-------------
FX Impact MK3 .22 700mm


Print Page | Close Window

Forum Software by Web Wiz Forums® version 10.14 - http://www.webwizforums.com
Copyright ©2001-2012 Web Wiz Ltd. - http://www.webwiz.co.uk