.22 barrel
Printed From: Kiwi Airgunners
Category: Technical
Forum Name: Pauly's Technical Area
Forum Description: Technical information, Modifications and DIY projects are all in here
URL: www.kiwiairgunners.co.nz/forum_posts.asp?TID=504
Printed Date: 23 Nov 2024 at 1:54pm
Software Version: Web Wiz Forums 10.14 - http://www.webwizforums.com
Topic: .22 barrel
Posted By: Pauly5
Subject: .22 barrel
Date Posted: 03 Sep 2020 at 8:25pm
|
Hi guys, I have one of those Zoraki pistols, but it has the short barrel. Does anyone have a bit of barrel I could use? The current one is 10 mm, so even a crosman barrel would be ok, but would need it to be about 250 mm long. PM me. |
Replies:
Posted By: dvlnme
Date Posted: 04 Sep 2020 at 7:06am
|
hi Paul,i have approx 300mm of crosman 22 barrel here mate,left over from pcp revolver project if of any use to u,let me know eh,swap u for approx same length of 177 barrel if u got some.no rush for some 177 barrel will send u 22 barrel if suits your purpose and sort out 177 barrel later. cheers mike
|
Posted By: Pauly5
Date Posted: 08 Sep 2020 at 11:20pm
|
Hi Mike, I don't have any .177 barrel, but I wanting to put a longer barrel in, so I can put a silencer on it. Current barrel isn't long enough. Happy to pay you for it? Let me know. Cheers Paul. |
Posted By: dvlnme
Date Posted: 09 Sep 2020 at 7:08am
|
barrel 320mm long and is the breech end mate and full factory diameter,so be good for your project,make me offer,as cant remember what cost. cheers mike
|
Posted By: Pauly5
Date Posted: 09 Sep 2020 at 7:42am
|
Hi Mike, what is that diameter? I need 10 mm to fit in the holding brackets, but would need to cut a 10 mm groove down to 8.5 at the breech end. I will send a picture soon, but it sounds good. |
Posted By: Pauly5
Date Posted: 09 Sep 2020 at 6:25pm
 The barrel diameter is 10 mm, with that waist section 8 mm diameter, starting 10 mm from the breech face. That is the breech end in the picture. I wouldn't be able to turn down the barrel with my baby lathe, so do you reckon you could do it for me and I will pay you on top of the cost of the barrel? |
Posted By: Pauly5
Date Posted: 09 Sep 2020 at 6:30pm
|
Total length 250 mm, which will give me about 60 mm out the end to make a silencer for it. |
Posted By: dvlnme
Date Posted: 11 Sep 2020 at 7:15am
|
sent you a PM mate,had trouble getting on forum for some reason had been shut out,so had get new password lol. cheers mike
|
Posted By: Pauly5
Date Posted: 11 Sep 2020 at 9:42am
|
uploads/8/Barrel-11092020093624.pdf" rel="nofollow - uploads/8/Barrel-11092020093624.pdf
|
Posted By: Pauly5
Date Posted: 11 Sep 2020 at 9:49am
|
Here's the dimensions for ya. What an effort getting this drawing into a file I could upload. really tested my IT skills. 
|
Posted By: dvlnme
Date Posted: 12 Sep 2020 at 7:34am
|
got the pdf mate will sort out next few days . cheers mike
|
Posted By: dvlnme
Date Posted: 15 Sep 2020 at 8:52am
|
does your factory barrel have any sort of pellet chamber at rear ???,do you want it cut to 250mm can leave longer if you want mate. cheers mike
|
Posted By: Pauly5
Date Posted: 15 Sep 2020 at 9:02am
|
Hi Mike, No, the lead in is just smoothed. The barrel closes up against the transfer port directly behind it, so the pellet is seated just like you would in a break barrel, except in this case the O ring is on the transfer port/valve body. Maybe just leave it longer, and I can cut it to length. Is that enough info? I can take better pictures a bit later.
|
Posted By: dvlnme
Date Posted: 16 Sep 2020 at 8:10am
|
all good mate,will just releave rifling a little so you can seat pellet etc,can leave barrel as long as possible and you cal trim and crown yourself. cheers mike
|
Posted By: dvlnme
Date Posted: 17 Sep 2020 at 7:31am
|
will finish your barrel today mate,pm me where you want it sent.or give me a call on 02102785078. cheers mike
|
Posted By: Pauly5
Date Posted: 24 Sep 2020 at 6:45pm
 
|
Posted By: dvlnme
Date Posted: 24 Sep 2020 at 7:04pm
|
thats not bad eh!!must be that extra barrel length,obviously it fitted well,whats accurracy like?you can still polish muzzle crown too,shouldnt be any burrs as couldnt see any,but you never know till its shoot if crown is right eh.looks good with the exta barrel length too. cheers mike
|
Posted By: J-S
Date Posted: 02 Oct 2020 at 2:40pm
|
Nice! suppressor next?! ------------- https://www.instagram.com/js_airguns/" rel="nofollow - J S Airguns Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
Posted By: Pauly5
Date Posted: 06 Oct 2020 at 7:10am
| Yep, that's the plan. Good old carbon fibre. |