|
Could any 3d print one of these |
Post Reply 
|
Page <123> |
| Author | |
nunga 
Forum Moderator 
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 825 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 02 Mar 2023 at 4:34pm |
|
Had lots of problems with the 3d printer, just got it out of the shop and im printing some test samples now and i should have something to show tomorrow
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
 |
|
|
kruzaroad
Senior Member 
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 1719 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2023 at 7:12pm |
|
Not something I could do without popping a few brain cells.
Cheers How your hand holding up |
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 825 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2023 at 7:10pm |
|
wasnt as bad as i thought, didnt take that long
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 1719 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2023 at 7:05pm |
|
Yep that looks the part. Take much programming?
|
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 825 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Feb 2023 at 7:03pm |
|
Is this what you are after?  |
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
Billbobnz
Senior Member
Joined: 13 Jun 2020 Location: Ashburton Status: Offline Posts: 784 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Feb 2023 at 7:05pm |
|
Take care and get well sir
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 1719 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Feb 2023 at 9:31am |
|
I hope your hand comes out OK.
Just as you do Nunga, if you can with a crook hand all good if not sweet as. |
|
|
|
|
nunga
Forum Moderator
Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 825 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Feb 2023 at 9:18am |
|
Im off work for a few weeks, recovering form reconstructive surgery on my hand. Ill have a play with the printer and see what i can come up with. might be a little while as im right handed and its my right hand they cut up lol...finding out the hard way how difficult things are using one hand for everything ha ha
|
|
|
2nd place HP springer - WFTF World Championships 2014
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 1719 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 Dec 2022 at 7:26pm |
|
OK final design, sorry.
Lets go for just the tab. If could print up a ring with tab @ 55.20mm inner circumference and a width of 17mm, locking screws That would be awsome. Me and sand paper will fine tune the inner ring to ngsnug fit. I'll sort out gluing in some indevidualy made pieces to sit between ridges and glue them in and sand the whole thing to size of ring. Leave design and thickness of tab and ring to you. 3mm be max thickness or ring before it touches cylinder. That work for you? |
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 1719 |
Post Options
Thanks(0)
Quote Reply
Posted: 14 Dec 2022 at 6:58pm |
|
Actually that sounds like a hassel,
If you want to print me up the ring with tab and locking screws. That would be awsome and I'd appresiate it. When it gets here I'll buy some plastic make wedges to fit between ridges, and then glue them into the inside of the ring in situ and that should work awsome and be a Taylor fit. |
|
|
|
|
Post Reply
|
Page <123> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options