Kiwi Airgunners Homepage
Forum Home Forum Home > Technical > Pauly's Technical Area
  New Posts New Posts RSS Feed - .22 barrel
  FAQ FAQ  Forum Search   Register Register  Login Login

.22 barrel
 Post Reply Post Reply Page  12>
Author
Message
  Topic Search Topic Search  Topic Options Topic Options
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Topic: .22 barrel
    Posted: 03 Sep 2020 at 8:25pm
Hi guys,

I have one of those Zoraki pistols, but it has the short barrel. Does anyone have a bit of barrel I could use? The current one is 10 mm, so even a crosman barrel would be ok, but would need it to be about 250 mm long.

PM me.
Back to Top
dvlnme View Drop Down
Senior Member
Senior Member
Avatar

Joined: 30 May 2017
Location: taranaki
Status: Offline
Posts: 519 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dvlnme Quote  Post ReplyReply Direct Link To This Post Posted: 04 Sep 2020 at 7:06am
hi Paul,i have approx 300mm of crosman 22 barrel here mate,left over from pcp revolver project if of any use to u,let me know eh,swap u for approx same length of 177 barrel if u got some.no rush for some 177 barrel will send u 22 barrel if suits your purpose and sort out 177 barrel later.
 cheers mike
Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 08 Sep 2020 at 11:20pm
Hi Mike,

I don't have any .177 barrel, but I wanting to put a longer barrel in, so I can put a silencer on it. Current barrel isn't long enough. Happy to pay you for it? Let me know.

Cheers Paul.
Back to Top
dvlnme View Drop Down
Senior Member
Senior Member
Avatar

Joined: 30 May 2017
Location: taranaki
Status: Offline
Posts: 519 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dvlnme Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2020 at 7:08am
barrel 320mm long and is the breech end mate and full factory diameter,so be good for your project,make me offer,as cant remember what cost.
 cheers mike
Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2020 at 7:42am
Hi Mike, what is that diameter? I need 10 mm to fit in the holding brackets, but would need to cut a 10 mm groove down to 8.5 at the breech end. I will send a picture soon, but it sounds good.
Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2020 at 6:25pm


The barrel diameter is 10 mm, with that waist section 8 mm diameter, starting 10 mm from the breech face.
That is the breech end in the picture. I wouldn't be able to turn down the barrel with my baby lathe, so do you reckon you could do it for me and I will pay you on top of the cost of the barrel?



Edited by Pauly5 - 09 Sep 2020 at 6:26pm
Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 09 Sep 2020 at 6:30pm
Total length 250 mm, which will give me about 60 mm out the end to make a silencer for it.
Back to Top
dvlnme View Drop Down
Senior Member
Senior Member
Avatar

Joined: 30 May 2017
Location: taranaki
Status: Offline
Posts: 519 		Post Options Post Options   Thanks (0) Thanks(0)   Quote dvlnme Quote  Post ReplyReply Direct Link To This Post Posted: 11 Sep 2020 at 7:15am
sent you a PM mate,had trouble getting on forum for some reason had been shut out,so had get new password lol.
 cheers mike
Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 11 Sep 2020 at 9:42am
uploads/8/Barrel-11092020093624.pdf



Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1172 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 11 Sep 2020 at 9:49am

Here's the dimensions for ya. What an effort getting this drawing into a file I could upload. really tested my IT skills.




Edited by Pauly5 - 11 Sep 2020 at 10:20am
Back to Top
 Post Reply Post Reply Page  12>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.031 seconds.