Kiwi Airgunners Homepage
Forum Home Forum Home > Technical > Pauly's Technical Area
  New Posts New Posts RSS Feed - scope creep
  FAQ FAQ  Forum Search   Register Register  Login Login

scope creep

 Post Reply Post Reply
Author
Message
nunga View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 08 Mar 2013
Location: Pukekohe
Status: Offline
Posts: 824
Post Options Post Options   Thanks (0) Thanks(0)   Quote nunga Quote  Post ReplyReply Direct Link To This Post Topic: scope creep
    Posted: 13 Jun 2015 at 10:16am
As most of you guys know i have had problem after problem with my scope moving so this week i decided to see if i can fix this once and for all. I did get a set of adjustable mounts but they didnt look up to the job and i thought they might move more than what it is moving now. so what to do? I was Talking to Brian at the last shoot and he said i should try lapping the mounts because these cheaper mounts sometimes are not very round. I decided to take his advice but also i will take it to the next level.


So this is what i have done. I machined up a bit of alloy bar to exactly 29.00mm. I have some 120 grit emery tape which i attached to the bar with some double sided tape. the emery tape is half a mill thick so this will give me the 30.00mm needed to sand the mounts






I am using shims at the back of my T50 scope and this is causing the scope to move because the shims are half a mil thick and the scope is not sitting flat on the mounts. So what i decided to do was pack the back of my alloy bar up so it is half a mill thicker than the front and when i am sanding it will sand the mounts on the right angle for the scope to sit flat on the mounts...do you follow me?









So the bar is higher at the back and i packed it up with the same thickness as the packers in using on the scope. but i do not use emery tape for the back mount yet. i only want the front mount to be sanded. this will cut the right angle that i need for the scope to sit flat. once the front mount is sanded in all the way and is at the angle i need i swap the it around so now the back mount will be sanded and not the front. This gives me two mounts sanded on a angle so when i put my scope back on with the half mill packers the scope will be sitting flat on the mounts and should get rid of the scope creep.



Edited by Nunga - 13 Jun 2015 at 10:18am
2nd place HP springer - WFTF World Championships 2014



Back to Top
Pauly5 View Drop Down
Senior Member
Senior Member
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1148
Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 13 Jun 2015 at 6:23pm
Not that I know much, but what material are the Packers? What if you used something like self actuating tape that will mold to what's needed and grip at the same time. Looks like you have it sorted though.
Back to Top
nunga View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 08 Mar 2013
Location: Pukekohe
Status: Offline
Posts: 824
Post Options Post Options   Thanks (0) Thanks(0)   Quote nunga Quote  Post ReplyReply Direct Link To This Post Posted: 14 Jun 2015 at 1:32pm
The packers are plastic so they dont compress when you do the bolts up  like the those tapes do.
2nd place HP springer - WFTF World Championships 2014



Back to Top
(pink)MIST View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 09 Mar 2013
Location: Hamilton
Status: Offline
Posts: 465
Post Options Post Options   Thanks (0) Thanks(0)   Quote (pink)MIST Quote  Post ReplyReply Direct Link To This Post Posted: 16 Jun 2015 at 7:44pm
What happened to the anti creep piece you were making?
NZAFTA President
1st place HP springer - 2014 WFTF Worlds
1st place HP springer - 2014 Nats

AA TX200 MK111, Optisan Viper 8-32x60 JSB. VMach, TbT, maestro design.
Back to Top
nunga View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 08 Mar 2013
Location: Pukekohe
Status: Offline
Posts: 824
Post Options Post Options   Thanks (0) Thanks(0)   Quote nunga Quote  Post ReplyReply Direct Link To This Post Posted: 18 Jun 2015 at 11:48pm
It needs some fine tuning which im working on.
2nd place HP springer - WFTF World Championships 2014



Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.047 seconds.