Kiwi Airgunners Homepage
Forum Home Forum Home > For Sale / Wanted > Wanted
  New Posts New Posts RSS Feed - Aluminium tube or carbon fibre
  FAQ FAQ  Forum Search   Register Register  Login Login

It looks like everything is working again. But it seems very slow to post messages now. Please report any buds and i will try to sort it out

Aluminium tube or carbon fibre
 Post Reply Post Reply Page  12>
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
kruzaroad View Drop Down
Senior Member
Senior Member
Avatar

Joined: 03 Jul 2022
Location: Hastings 4 now
Status: Offline
Posts: 2443 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruzaroad Quote  Post ReplyReply Direct Link To This Post Topic: Aluminium tube or carbon fibre
    Posted: 17 May 2024 at 2:53pm
Should have grabbed the air chief. Could have mucked around with Drilling holes along end of barrel and making a suppressor that went length of barrel.
Its nicely wrapped up in plastic, sealed with tape and sitting in farm tip now. (I couldn't bring myself to just throw it over the bank as it was )
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1475 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 2:37pm
Yes, I had heard someone describe that the air hits the washers, but the angle did what you say Kruz. Definitely my next project when I get some more suitable material.
Back to Top
kruzaroad View Drop Down
Senior Member
Senior Member
Avatar

Joined: 03 Jul 2022
Location: Hastings 4 now
Status: Offline
Posts: 2443 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruzaroad Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 2:23pm
Think to your barrel may help decide.
I've had 2 of Pauly5 suppressors.
Both carbon fiber, both went on crossman barrels, which were rather thin so the carbon fiber was great due to weight.
Definitely for the 1322 as the barrel is longer.
Read an artical or watched a video on a suppressor and the baffles were at 60" I think it was, that was because it was high power and apparently that angle took a lot of pressure away from the baffle as it wasn't flat.

Edited by kruzaroad - 17 May 2024 at 2:25pm
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1475 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 1:55pm
They are good for making supressors, as the tube is true and lightweight.

They do have a sharper tone, as the wall is quite thin though. I have made a few, and have just used flat washers as baffles with hair curlers supporting a felt like material. This works well enough for lower powered guns, but I don't think its efficient on higher powered guns.

I would like to try a shaped baffle insert, but you end up using a lot of material just to cut the baffle shape out of a solid bar of alu, or delrin.
Back to Top
kruisn View Drop Down
Member
Member


Joined: 11 May 2023
Location: Far North
Status: Offline
Posts: 9 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruisn Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 9:13am
OOOps sorry (Angry predictive text?) I meant "suppressor" as in the topic above. I was curious how to build 
one and if they were practical and useful.
Back to Top
kruzaroad View Drop Down
Senior Member
Senior Member
Avatar

Joined: 03 Jul 2022
Location: Hastings 4 now
Status: Offline
Posts: 2443 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruzaroad Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 8:13am
https://youtu.be/0Wj34GNI_90?si=rBo4ZpgvR4SPt99Q
Something like this?
Back to Top
kruzaroad View Drop Down
Senior Member
Senior Member
Avatar

Joined: 03 Jul 2022
Location: Hastings 4 now
Status: Offline
Posts: 2443 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruzaroad Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 5:47am
Are you talking about a compressor tank or building the the actual compressor out of it?
Back to Top
kruisn View Drop Down
Member
Member


Joined: 11 May 2023
Location: Far North
Status: Offline
Posts: 9 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruisn Quote  Post ReplyReply Direct Link To This Post Posted: 17 May 2024 at 5:26am
How would a person go about making a compressor for an air rifle out of carbon fibre or aluminium?
and would it make a lot of difference?
Question
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1475 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 16 May 2024 at 10:39pm
Keen to hear how you go machining it. I use a hacksaw to cut it then mill the end to length and perpendicular. It get's fine burrs from the fibres, but a fine file or sandpaper works ok to remove them.
I suspect it will work out better if it was supported maybe with a wooden dowel.
Back to Top
Stuart View Drop Down
Senior Member
Senior Member


Joined: 21 Feb 2017
Location: North Canterbur
Status: Offline
Posts: 137 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Stuart Quote  Post ReplyReply Direct Link To This Post Posted: 15 May 2024 at 4:52am
All sorted thanks
Back to Top
 Post Reply Post Reply Page  12>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.047 seconds.