|
Smith & Wesson 78G restore project |
Post Reply 
|
Page <12 |
| Author | |
J-S 
Senior Member 
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 16 Jan 2021 at 11:14pm |
|
Cheers, yes it certainly won’t be original.
There is something charming about the original flawed finish though, so I went and got a Matt spray to test.. it may be closer to the original finish based on the small test piece. Not so much sheen. So back to stripping! The spray comes off easier than the factory finish so it won’t take much to strip back to metal and try again!  |
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
 |
|
|
dvlnme
Senior Member
Joined: 30 May 2017 Location: taranaki Status: Offline Posts: 519 |
Post Options
Thanks(0)
Quote Reply
Posted: 17 Jan 2021 at 10:21am |
|
best wearing paints are those you can bake on they dont chip etc like normal spray paint and wear better,i have used wood stove paint before,that bakes on at low temps so have preheated gun parts painted them and put in home oven at pout 100d /c for good results,these are usually flat finishs so do work well and look good/worth a try cheers mike
|
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 Jan 2021 at 11:05am |
|
This matt paint is a primer / paint apparently suitable for directly coating... (according to their marketing claims...) but I will try curing it in the hooded BBQ at around 100C. The wife may not be too please with spray paint fumed in the oven..
The good thing about these is that there are not many parts that move against other parts so there shouldn't be a lot of friction wear on the paint. I did consider the high temp engine paints / stove paints, but i wasnt sure about the finish; this one was priced in between the standard sprays and those specialist ones and I think it should do fine.. if not I can always strip it a third time!
|
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
dvlnme
Senior Member
Joined: 30 May 2017 Location: taranaki Status: Offline Posts: 519 |
Post Options
Thanks(0)
Quote Reply
Posted: 22 Jan 2021 at 9:19am |
|
know what you mean about the wife and the oven been there done that and still got the scars because got caught by she who must be obeyed when comes to the stove.had excellent results from stove and exhaust paints they all come out with nice flat finish after heating,wont take long for the paint smell to go away on the barbi steaks eh!!.
cheers mike
|
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Jan 2021 at 3:22pm |
|
Had a spare couple of hours and got the Matt black spray on. It went on ok, with a couple of smudges that would be mostly hidden under the grips. Sprayed and hung until just touch dry, then hung outside in the sun for an hour before barbecuing... heated at around 100-120 degrees for about 40 minutes then cooled under the hood.
 The finish feels good - it doesn’t have that plastic feel spray paints can have and no tacky feeling. Slightly more sheen than original finish but pretty close and if nothing else will have a little more character than the original. The top section had a nice even finish.. until it dropped from hanging! I caught it so no damage, but the finish needed to be stripped AGAIN, and is now ready to painted again when I have a spare minute. 
|
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
dvlnme
Senior Member
Joined: 30 May 2017 Location: taranaki Status: Offline Posts: 519 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jan 2021 at 3:19pm |
|
just shows you how versitile a barby is eh.
cheers mike
|
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 27 Jan 2021 at 4:48pm |
Needs a good scrub though - looks like i used it as a spray booth for the black....
 |
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
dvlnme
Senior Member
Joined: 30 May 2017 Location: taranaki Status: Offline Posts: 519 |
Post Options
Thanks(0)
Quote Reply
Posted: 31 Jan 2021 at 8:33am |
 thats looking great mate,factory finish was never that good on these,you are rebuilding a shooter not trying to restore it to origional anyway just guna be a real nice shooter now and one you can enjoy and be proud of and that in the end is what matters. cheers mike
|
|
|
|
|
J-S
Senior Member
Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425 |
Post Options
Thanks(0)
Quote Reply
Posted: 18 Mar 2021 at 12:45pm |
|
Had a few minutes spare and got the pistol back together. Its not perfect, has a couple of marks already, but its much tidier than it was. Its shooting around 380fps with H&N FTT, which sounds about right, so the hammer and the trigger replacement are functioning. The safety isnt working properly, must be something to do with the hammer / trigger upgrade, but one shouldnt rely on a mechanical safety over proper discipline.. I had a mate cut a vinyl graphic for a hard case; the same logo / branding / "Co2 Air Pistol" that appeared on their original box, in S&W Blue.  |
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
Post Reply
|
Page <12 |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
dvlnme wrote: