|
The $100 challenge..... |
Post Reply 
|
Page <1 1617181920 32> |
| Author | |
jwabfrog 
Senior Member 
Joined: 13 Nov 2021 Location: Thames Status: Offline Posts: 154 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 06 Sep 2023 at 3:53am |
|
same goes for Bilbo's barrel machining work
|
|
 |
|
|
kruzaroad
Senior Member
Joined: 03 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2472 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2023 at 4:03am |
|
Can't see the point in getting to complicated on trigger for this gun.
A simple stop for trigger seems enough for me. Another idea I had, but won't be doing due to lack of tools, was to bore a small hole into the breech block, to the bottom left or right of the barrel. Thread the top so a small cap with center drilled out could be screwed over the top of a spring and ball bearing put into the hole, and a shallow receiving hole on other side for the bearing to lock into. Barrel lock. In theory would hold barrel in same place when closed. |
|
|
|
|
KiwiTR6
Senior Member
Joined: 04 Nov 2022 Location: Stratford Status: Offline Posts: 330 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2023 at 5:19am |
Thanks frog, I'm really not that talented. I sit at a desk all day so this sort of stuff is my way of de-stressing
 Edited by KiwiTR6 - 06 Sep 2023 at 5:54am |
|
|
FX King 600 .22
FX Dreamline Classic .22 Diana Outlaw .22 Air Arms S410 .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 Custom .22 Crosman 2250 Custom .22 Brocock Grand Prix .22 |
|
|
|
|
Billbobnz
Senior Member
Joined: 14 Jun 2020 Location: Ashburton Status: Offline Posts: 882 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2023 at 4:10pm |
|
Righto, Ive got the barrel refitted, modified the original breech seal and got it lined up perfectly horizontal.
Have shimmed breech to remove the lateral movement. I need to make another breech pivot bolt but it's fitted together ok in the meantime to put it back together tomorrow to retest it at 10m. Fingers crossed....... |
|
|
|
|
KiwiTR6
Senior Member
Joined: 04 Nov 2022 Location: Stratford Status: Offline Posts: 330 |
Post Options
Thanks(0)
Quote Reply
Posted: 06 Sep 2023 at 4:11pm |
|
Sourced some O-rings today from the local engineer and turned up a nylon spacer to bring the O-ring out about 0.5mm beyond the breech. I then fastened it to the spacer with some E6000 glue and closed the breech while it set. The breech now closes completely and when I put the barrel in the vice and applied pressure to the cylinder there was no play at all. The barrel and cylinder aren't concentric with several degrees of difference between the centreline of each. I'm not going to try and correct this though as now that the breech is solid a scope adjusted to suit should work fine (I assume?). I also had time to cut a groove in the piston to take a PTFE ring rather than the buttons I was planning to fit. The piston body was too flexible to grip in the 4-jaw so I held it by the centre shaft and centralised it with my dial gauge as best I could. The thing squealed like a pig as the parting tool chattered away trying to cut the groove but I got there eventually. Not pretty, but it should work. Hopefully I'll have time tomorrow to make the ring then it can be assembled, although I want to to crown the barrel before I test it again.  |
|
|
FX King 600 .22
FX Dreamline Classic .22 Diana Outlaw .22 Air Arms S410 .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 Custom .22 Crosman 2250 Custom .22 Brocock Grand Prix .22 |
|
|
|
|
J-S
Senior Member
Joined: 20 Oct 2014 Location: Auckland Status: Offline Posts: 451 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2023 at 4:49am |
|
great efforts!
|
|
|
J S Airguns
Air Arms TX200('s) Theoben Sirocco HW77 FWB 300s Webley Patriot One or two others... Current projects: Too many.. |
|
|
|
|
Billbobnz
Senior Member
Joined: 14 Jun 2020 Location: Ashburton Status: Offline Posts: 882 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2023 at 3:35pm |
|
Gun is temporarily back together, I have taken slightly too much off the breech so the barrel is slightly upwards but is fixable. Definitely shooting much smoother.
My son came out (8yrs old) and decided right there and then to have a go. Got him on the cr600 and 3rd shot in was right on the bullseye at 10m. I think the air chief will become his first gun once I've finished with it |
|
|
|
|
Billbobnz
Senior Member
Joined: 14 Jun 2020 Location: Ashburton Status: Offline Posts: 882 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2023 at 3:36pm |
|
LOP is still slightly too long so may shorten the stock for him on the air chief but not untill I master the beast it is haha
|
|
|
|
|
kruzaroad
Senior Member
Joined: 03 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2472 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2023 at 4:04pm |
|
Sweet bb. Sounds like he will be showing you soon.
So how you gonna fix it? Shim or reface? |
|
|
|
|
Billbobnz
Senior Member
Joined: 14 Jun 2020 Location: Ashburton Status: Offline Posts: 882 |
Post Options
Thanks(0)
Quote Reply
Posted: 07 Sep 2023 at 4:06pm |
|
Will try shimming first
|
|
|
|
|
Post Reply
|
Page <1 1617181920 32> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options
jwabfrog wrote: