Kiwi Airgunners Homepage
Forum Home Forum Home > Technical > Reviews
  New Posts New Posts RSS Feed - .30 Hatsan Carnivore 135
  FAQ FAQ  Forum Search   Register Register  Login Login

.30 Hatsan Carnivore 135

 Post Reply Post Reply
Author
Message
mercs View Drop Down
Senior Member
Senior Member
Avatar

Joined: 24 Apr 2020
Location: Stratford
Status: Offline
Posts: 272
Post Options Post Options   Thanks (1) Thanks(1)   Quote mercs Quote  Post ReplyReply Direct Link To This Post Topic: .30 Hatsan Carnivore 135
    Posted: 05 Jun 2022 at 4:29pm
I wanted the springer version which was readily available at $650.

This is no lightweight and the cocking effort can be a workout.
Good body position and practised artillery hold gives results. 

Purchased for fun but found it can deal to pests and earn its keep.
750 pellets through with no issues. ($32 per 150)
Interesting that the actual barrel is only 11 inches in length but it shoots superbly.
Adjustable cheek piece is a winner, wish these were included on more rifles.

Good
adjustable cheek riser
adjustable shoulder pad
trigger firm but crisp and repeatable
metal finish
sights
Bad
really heavy to cock
had to send back for replacement.
Ugly
nah its a looker

Test Results
HatsanCarnivore 135 .30
Pellet BrandJSB Match
Pellet typeDiabolo
Average fps547
Grains44.75
Grammes2.9
foot pounds29.74
Joules40.32

I prefer to use it with a red dot but the existing fibre sights are very usable.

SportsMatch Dampa mount was purchased to give scopes some protection.
The rifle has both dovetail and picatinny rails, I used both rails without any movement or slippage but the recoil lends itself towards picatinny fittings.

50 shot test of 10 pellet groups from 10, 15, 20, 25 and 30 yards were great with very little pellet drop.
One of the best 25 yard bench rest groups I have obtained which was a real surprise.
Hits with real force at 40 yards but holdover changes quickly so mil-dots are useful for longer ranges.

Seen here with a Stealth 4-14x44 30mm ($200) surprisingly accurate.

Fitted with a Stealth Red Dot ($80) and it starts to reveal true potential.



Warranty
Liked it out of the box and initial accuracy using the sights seems good, but I grew suspicious and on investigation the barrel pivot cannot have been fitted correctly so barrel was "drooped" and with effort I could physically move it when latched for firing. It was returned and immediately replaced with a good unit. Disappointing that it made it out of the factory.

Scopes - Definitely requires a purpose built air rated scope.
Stealth 4-14x44 - failed, nice to use fast acquisition.
NS AirKing 2-7x32AO - failed, accurate and very usable for targets and plinking.
NS 3-9x40 so far so good but early days, not so backyard friendly as the AirKing.

Target - this was the day one standing shots taken which I thought showed some promise.


Pellets from left .177, .20, .22, .25 & .30

Back to Top
dvlnme View Drop Down
Senior Member
Senior Member
Avatar

Joined: 30 May 2017
Location: taranaki
Status: Offline
Posts: 519
Post Options Post Options   Thanks (0) Thanks(0)   Quote dvlnme Quote  Post ReplyReply Direct Link To This Post Posted: 06 Jun 2022 at 9:02am
now thats one serious springer
 cheers mike
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 13 Jun 2020
Location: Ashburton
Status: Offline
Posts: 867
Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 06 Jun 2022 at 7:58pm
Evening all, sorry I haven't been on for ages... 

Awsome review. 

I still have these one my wish list. My Hatsan 125 sniper in .25cal is still one of my favorites and is very accurate out to 60m. My rifle after 50-100 shots the breech was soooo sloppy, the movement was laterally so the groupings were a side to side pattern, i shimmed the side of the breech with some shim steel and re tightened it all up and that sorted that. The only other issue is the vortex gas piston in mine lost its air (vortex are high pressure air not nitrogen apparently) still waiting on replacement parts with no signs on the horizon of it coming anytime soon.......! I should just refurb it myself (you can adjust the pressure in the ram with a pcp probe and hand pump. 


Back to Top
 Post Reply Post Reply
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.119 seconds.