Kiwi Airgunners Homepage
Forum Home Forum Home > Technical > Pauly's Technical Area
  New Posts New Posts RSS Feed - Pistol build
  FAQ FAQ  Forum Search   Register Register  Login Login

Pistol build
 Post Reply Post Reply Page  <1 567
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
kruzaroad View Drop Down
Senior Member
Senior Member
Avatar

Joined: 02 Jul 2022
Location: Hastings 4 now
Status: Offline
Posts: 2284 		Post Options Post Options   Thanks (0) Thanks(0)   Quote kruzaroad Quote  Post ReplyReply Direct Link To This Post Posted: 12 Oct 2023 at 5:13pm
Looks awsome.
Why did it take 9 shots to hit the 600fps mark?
Ave for first 9 shots = 578 fps
Ave for next 17 shots at (600fps +) = 658 fps.
Thats a 80fps gain.
Like wise the last 6 shots
Ave =571 fpe (no calculated decimals but was 571.5)
Is a 87 fps drop.
The drop off at the end I understand.
The ones at front I don't.
If it's just it needed time to settle in I'd say you'd be closer to 650fps.
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 12 Oct 2023 at 10:27am
So my first fill was around 1800 psi and I shot it down to around 800 psi.
I used JSB 18.13 grn pellets.
33 usable shots and quite a gentle power curve. The variation between shots jumped about, but as I was shooting this string I was shooting groups and on paper it was a dead rabbit every shot.
Hopefully in the future I can refine this with trialing different spring tension and addition of a hammer tension adjuster to balance the valve and hammer. Shot string copied below.

1568
2586
3565
4563
5568
6586
7596
8588
9584
10608
11616
12622
13622
14607
15640
16622
17639
18614
19612
20641
21623
22641
23632
24621
25616
26613
27608
28598
29584
30582
31566
32559
33540
AVG600.9090909

I'm not after perfection, and to me it's a victory so far enjoying shooting it. I have teamed this up with a cheap hand pump and it only takes 50 strokes to fill to around 1800 psi according to the gauge on the pump. It's turning out to be a good little combo.
Back to Top
J-S View Drop Down
Senior Member
Senior Member


Joined: 19 Oct 2014
Location: Auckland
Status: Offline
Posts: 425 		Post Options Post Options   Thanks (0) Thanks(0)   Quote J-S Quote  Post ReplyReply Direct Link To This Post Posted: 11 Oct 2023 at 11:56am
Pretty bloody cool..
J S Airguns
Air Arms TX200('s)
Theoben Sirocco
HW77
FWB 300s
Webley Patriot
One or two others...

Current projects:
Too many..
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 11 Oct 2023 at 10:05am


Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 10 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1410 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 11 Oct 2023 at 9:55am
Over the past couple of months I have been inspired to build a pcp pistol. I do plan to build a breech, but at this stage I am basically converting a Crosman 22XX from CO2 to HPA using the trigger frame and steel breech.
Inspiration to do this is from a couple of very clever people that have given me good advise and the recent purchase of a small vertical mill has rocketed my confidence in build quality.

This won't be a long thread, but you should get the general idea of what i've done.

I started looking at other designs in both the big bore and lower power design. The possibilities and concepts rattled around my brain for a while and I started off planning to use the std valve system that came in the 22XX.  I ended up using a bigger sized tube, and so I had to make my own valve and hammer system.

My main concern in all of this was safety. So after getting all the info together I felt good about what I was to do with a 3  x safety factor for retaining the pressure. With this sorted it gave me a base to work off.

I didn't know what sort of performance the pistol would produce, but I have been pleasantly surprised and now have a base to work off for future build and refinements.

Photos show a few different stages including my trial and error parts. I basically built the pistol twice. This was a good idea as it meant the finished item had minimal adjustments made to it, and my measurements are recorded, so each build will be quicker.

Photo to come in another post. Thought i'd get the words done and dusted first. I will also share a bit more detail about it's performance too.
Back to Top
 Post Reply Post Reply Page  <1 567
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 0.066 seconds.