Gamo trigger guard

Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic

   That trigger guard is not plastic out a packet from China. Just plain good. Is the curved bit held to the plate by bent tabs?I found some aluminium solder that engineers might know about but DIY may not;quite expensive from Tradezone and you need a torch to get everything hot. Butane torch is hot enough. I think aluminium melts at 1200 degrees C and the solder at about 650. I was surprised how strong the aluminium solder is. Much stronger than lead tin solder and of course that is no good for aluminium.
The solder would not be as good aluminium welding but you need special gear and special skill for that.

Author	Message Topic Search Topic Options Post Reply Create New Topic Printable Version Translate Topic
Novagun Members Profile Send Private Message Find Members Posts Add to Buddy List Groupie Joined: 13 Dec 2016 Location: Wellington Status: Offline Posts: 62	Post Options Post Reply Quote Novagun Report Post Thanks(0) Quote Reply Posted: 31 May 2017 at 12:44pm
	That trigger guard is not plastic out a packet from China. Just plain good. Is the curved bit held to the plate by bent tabs? I found some aluminium solder that engineers might know about but DIY may not;quite expensive from Tradezone and you need a torch to get everything hot. Butane torch is hot enough. I think aluminium melts at 1200 degrees C and the solder at about 650. I was surprised how strong the aluminium solder is. Much stronger than lead tin solder and of course that is no good for aluminium. The solder would not be as good aluminium welding but you need special gear and special skill for that.

J-S Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Senior Member Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425	Post Options Post Reply Quote J-S Report Post Thanks(0) Quote Reply Posted: 26 May 2017 at 9:16am
	No I haven't, it was a hand me down that I have never really used. I got it serviced not long ago and it shoots 2-3" groups so doesn't get a lot of attention along side the TX200 or FWB! Its twangy, harsh and with a terrible trigger, but they are from a time before Gamo started pumping out 25 models each year and seems to have a better build quality. I think as you say, open it up and give it a good polish etc will help. I chronied it years ago and it was doing 17-18fpe, so perhaps collapsing a coil or two and bringing it down to 15-16fpe would help the feel of it and keep it with enough power to hunt with..

xyon Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 20 Dec 2016 Location: Canterbury Status: Offline Posts: 135	Post Options Post Reply Quote xyon Report Post Thanks(0) Quote Reply Posted: 26 May 2017 at 9:09am
	Thanks, have you done any work on your hunter 440?
	--- My favourites springer - Diana 52 PCP - FX Wildcat III

J-S Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Senior Member Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425	Post Options Post Reply Quote J-S Report Post Thanks(0) Quote Reply Posted: 26 May 2017 at 9:01am
	Looks good, perhaps a nice polish would bring it up nicely rather than paint - add a bit of bling and show its a little different from the standard plastic jobby.

xyon Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 20 Dec 2016 Location: Canterbury Status: Offline Posts: 135	Post Options Post Reply Quote xyon Report Post Thanks(0) Quote Reply Posted: 25 May 2017 at 9:34pm
	Hmm, I thought about ringing Youngs, but in a fit of madness I decided to make my own. This is the result of several hours work attacking some 3mm Al sheet with a hacksaw, file and drill. I say mad, since as well as the time, I expect the price of some decent paint is going to be about the same as buying a new one I just got the hunter, so my plan is to test it for accuracy first before putting a lot of time into it. If its good, I will give it a trigger job, de-burr, polish, new seal and maybe convert to gas spring. The barrel also needs re-bluing. If not I may put the stock on my Crosman crusher, which seems to shoot quite nicely.
	--- My favourites springer - Diana 52 PCP - FX Wildcat III

J-S Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Senior Member Joined: 19 Oct 2014 Location: Auckland Status: Offline Posts: 425	Post Options Post Reply Quote J-S Report Post Thanks(0) Quote Reply Posted: 25 May 2017 at 3:54pm
	I took my 440 to Youngs a couple of weeks ago for a spring and it came back with a new trigger guard because my one was broken (obviously common!) So he must have them in stock.. Out of interest, have you done any internal work on yours?

nunga Members Profile Send Private Message Find Members Posts Visit Members Homepage Add to Buddy List Forum Moderator Joined: 08 Mar 2013 Location: Pukekohe Status: Offline Posts: 1009	Post Options Post Reply Quote nunga Report Post Thanks(0) Quote Reply Posted: 24 May 2017 at 2:56pm
	Might have one of those...let me have a look and ill get back to you
	2nd place HP springer - WFTF World Championships 2014

xyon Members Profile Send Private Message Find Members Posts Add to Buddy List Senior Member Joined: 20 Dec 2016 Location: Canterbury Status: Offline Posts: 135	Post Options Post Reply Quote xyon Report Post Thanks(0) Quote Reply Posted: 24 May 2017 at 2:46pm
	I'm refinishing the sock on an old hunter 440, the trigger guard is missing so I'm looking for a replacement. I think the Crosman quest would have the same sized one. I can get one shipped from the uk for 10 quid, but I thought I would ask here first. And the guard I need.
	--- My favourites springer - Diana 52 PCP - FX Wildcat III