Kiwi Airgunners Homepage
Forum Home Forum Home > General > Flub's General Discussion
  New Posts New Posts RSS Feed - The $100 challenge.....
  FAQ FAQ  Forum Search   Register Register  Login Login

The $100 challenge.....
 Post Reply Post Reply Page  <1 1415161718 32>
Author
Message Reverse Sort Order
  Topic Search Topic Search  Topic Options Topic Options
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jun 2020
Location: Ashburton
Status: Offline
Posts: 882 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 4:15pm
Thanks Kiwi, I'm so far down digging the hole I'm in I just having to plough on....

I do like the seal and top hat you've done..

Somewhere at work I have some spare polymer parts of different densities left over from a job I did ages ago. I'm going to attempt to make a new breech seal with these and possibly piston seal if they are wide enough.
Back to Top
KiwiTR6 View Drop Down
Senior Member
Senior Member


Joined: 04 Nov 2022
Location: Stratford
Status: Offline
Posts: 330 		Post Options Post Options   Thanks (0) Thanks(0)   Quote KiwiTR6 Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 4:00pm
Bill, you're more game than I am! I'm going to leave the barrel in place and try to crown it by hold the breech block in my 4-jaw and support the other end in my fixed steady.  Will take a little bit of setting up and I'm not sure it'll work but I'll give it a go.

I finished my PTFE seal and made up a top hat (I think I've got it right this time?) so only the buttons to go. I've put a rubber washer under the seal to take the shock and hopefully protect the sharp leading edge I've formed.

Paul, this is the link to the case hardening powder I've just ordered > https://www.ebay.com/itm/225611131542





FX King 600 .22
FX Dreamline Classic .22
Diana Outlaw .22
Air Arms S410 .22
Cometa Fenix 400 .177
Weihrauch HW50 .177
Crosman 2240 Custom .22
Crosman 2250 Custom .22
Brocock Grand Prix .22
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1527 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 1:25pm
Looking good!
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jun 2020
Location: Ashburton
Status: Offline
Posts: 882 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 12:09pm
I should be able to shim something into it.

I've shortened the barrel and it's awesome to look down and have a straight barrel! Took a little off the front and refaced it and will recrown it tomorrow. Also need to do the recess for the seal





Edited by Billbobnz - 05 Sep 2023 at 12:09pm
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1527 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 10:44am
How hard would it be to make a whole new breech block? Or should I say, is it worth doing that?
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jun 2020
Location: Ashburton
Status: Offline
Posts: 882 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 10:40am
I ended up taking slightly more off than I should have so breech is slightly upwards at the moment without the seal in
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jun 2020
Location: Ashburton
Status: Offline
Posts: 882 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 10:38am
Well um....

Was just looking at the breech seal to notice that it is shaped to match the angle of the breech!! Which means the breech angles down 6° and then the barrel angled back up from the end of the breech up 3°.....!

So..... I'm going to keep machining and shimming and re engineering untill I get it right..!

Which me luck 😂
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1527 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 9:28am
That looks nice. Will it effect the gap between comp tube and breech?
Back to Top
Billbobnz View Drop Down
Senior Member
Senior Member
Avatar

Joined: 14 Jun 2020
Location: Ashburton
Status: Offline
Posts: 882 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Billbobnz Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 8:09am
Just need to punch out the retaining pin beside the pivot hole then I used a punch and it came quite easily.

I've just machined my breech to 90° so looking much better
Back to Top
Pauly5 View Drop Down
Forum Moderator
Forum Moderator
Avatar

Joined: 11 Mar 2013
Location: Titahi Bay
Status: Offline
Posts: 1527 		Post Options Post Options   Thanks (0) Thanks(0)   Quote Pauly5 Quote  Post ReplyReply Direct Link To This Post Posted: 05 Sep 2023 at 7:48am
Bill, did it take much to get the barrel out of the block? Bit O heat?
Back to Top
 Post Reply Post Reply Page  <1 1415161718 32>
  Share Topic   

Forum Jump Forum Permissions View Drop Down

Forum Software by Web Wiz Forums® version 10.14
Copyright ©2001-2012 Web Wiz Ltd.

This page was generated in 1.940 seconds.