|
is it the seals |
Post Reply 
|
Page <1 34567 9> |
| Author | |
kruzaroad 
Senior Member 
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
 Post Options
 Thanks(0)
 Quote Reply
 Posted: 24 Aug 2022 at 2:07pm |
|
So went to a place called fasttrade Group limited, a mate reckoned was good. it had the screw for trigger, shim washers, moly grease,fine valve grinding paste in general every thing I've had a prick of time finding. sweet.
|
|
 |
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Aug 2022 at 5:44pm |
|
Well all back together, shooting worse than ever. Dropped the scope off. got 4 shots before wind jumped up for evening.
1 shot pulled knew it as soon as pulled trigger ( which by the way is so much better with new screw. Still heavy but not a long drawn out (bit like this whole episode lol) pull to sear engages. Nice and crisp. 25m open sight, not sighted in since new, old eyes so compromise on focus of back sight and target Shame only got 4 shots in. But better than scope by long shot. So the saga goes on. Gamo scope back on tomorrow, if that sux remove the gamo shock suppression base. remount scope in another set of rings I have. Its pretty close to being a give it away rifle at the moment. 
|
|
|
|
|
Billbobnz
Senior Member
Joined: 13 Jun 2020 Location: Ashburton Status: Offline Posts: 867 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Aug 2022 at 7:21pm |
|
Don't give it away, keep going and it could be that barrel after all. Let us know once the scope is back on how it's going
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 24 Aug 2022 at 8:39pm |
|
It's a a usable rifle now. I'll do more with open sight first. That last group was promising but to small to count.
If it is the barrel then I'm over it. If gamo won't replace not paying for one. Could still use it for recoil experiment. (put that washer back in to give it kick) Or I could just send it to you billbob. You can use it for parts, find a barrel for it. I'm wasting a lot of time I could be strolling the farm with the other gun. See how tomorrow goes. Or the next day |
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Aug 2022 at 8:29am |
|
Right still no accuracy groups to wide to hunt with don't think I'll bother with it any more. Rather be hunting with tx than mucking around with a gun that has been problematic since day one. Will ring up about barrel today. But that's it.
|
|
|
|
|
Pauly5
Forum Moderator 
Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1411 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Aug 2022 at 9:57am |
|
Yea, I have wondered how well that would work too. Same principle as a single stroke pneumatic in the way it stores air pressure. You would only need the one stroke to store more energy than an SSP can with one stroke, but with more weight in the gun.
I guess you would have to have the piston firing backwards so the plenum and valve is at the breech end too.
|
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Aug 2022 at 10:50am |
|
true. Don't have second trigger for piston release. Have lever system. Basic concept below.
 I'm thinking thumb size push pad, Thin strong steel rod. Pressure is not an issue as its not a shot stroke. A spring for helping release pressre if too tight Feasable.??? |
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Aug 2022 at 11:07am |
|
I think to me the separate release of the piston is the only way to get rid of impact when shooting.
I don't think that designing the release mechanism is outside the realm of ppl here. I don't think the initial piston firing is an issue for shooting as it can be done on way to shoulder after cocking. I don't see the mechanism adding to much height or weight. Or overly complicated. Would it be rated as a pcp as it has a precharged chamber? Edited by kruzaroad - 25 Aug 2022 at 12:19pm |
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 25 Aug 2022 at 12:26pm |
|
That's cool, gamo dude is going to see if they have any barrels ( they don't bring over spares) I've said any barrel that fits and is in good condition is fine. Doesn't have to have the suppressor fluting plastic surround.
Here's hoping |
|
|
|
|
kruzaroad
Senior Member
Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2284 |
Post Options
Thanks(0)
Quote Reply
Posted: 26 Aug 2022 at 2:27am |
|
Or flip the piston release mechanism upside down, extend the connecting rod, turn release lever into second trigger.
Side lever to reduce bulk underneath.  Cocking lever should be release lever sorry. Edited by kruzaroad - 26 Aug 2022 at 2:31am |
|
|
|
|
Post Reply
|
Page <1 34567 9> |
Tweet
|
| Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |
Topic Options