The $100 challenge..... |
Post Reply | Page <1 2526272829 32> |
Author | |
KiwiTR6
Senior Member Joined: 03 Nov 2022 Location: Stratford Status: Offline Posts: 269 |
Post Options
Thanks(0)
|
Definitely both have helped Kruz. The shots I did with other pellets types using the new hold were much better than before but the best I managed (noticeably) was with the selected small JSBs. I still plan to buy a tin of 4.50 and see if that has even smaller sizes that I can try. I think the bore in this gun could be undersized.
|
|
FX Wildcat MK111 BT Sniper .25
FX Dreamline Classic .22 Diana Outlaw .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 PCP Custom .22 Crosman 2250 PCP Custom .22 |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2258 |
Post Options
Thanks(0)
|
Eeek. Cheers timely reminder to put the vernier in the barrel.
Heading into town to get proper shim metal today and pellets. |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2258 |
Post Options
Thanks(0)
|
4.40mm on barrel diameter on lands.
Didn't want to put vernier edge into groove in case damaged. |
|
KiwiTR6
Senior Member Joined: 03 Nov 2022 Location: Stratford Status: Offline Posts: 269 |
Post Options
Thanks(0)
|
OK, so does my theory make sense then? If the skirt is larger then it will cause the pellet to spin, but if the head is larger what happens? Perhaps that's normal - I have no idea.
|
|
FX Wildcat MK111 BT Sniper .25
FX Dreamline Classic .22 Diana Outlaw .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 PCP Custom .22 Crosman 2250 PCP Custom .22 |
|
Pauly5
Forum Moderator Joined: 10 Mar 2013 Location: Titahi Bay Status: Offline Posts: 1401 |
Post Options
Thanks(0)
|
In theory the skirt should balloon out with the air pressure and fit anyway, but if the head is loose then it will come out randomly after bouncing around down the barrel, and if head too tight and it'll suffer too. This why the UK shooters buy sample batches of pellets and if they work well, they buy those batches in bulk.
So you gotta wonder if these cheap barrels are the same size all the way too.
|
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2258 |
Post Options
Thanks(0)
|
Measured both breach and muzzle.
Didn't appear choked. Got some air chief target pellets. Guy at shop said its what the gun club uses, so must be good pellets. I laughed. Still they may well be. No shim metal I could find so brought another v and will make a more refined verson. Brought a collapsible bucket for the plastic base support. Has two types in it. Both quite rigid but still have some form of flex. Thin. |
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2258 |
Post Options
Thanks(0)
|
So beat another aluminium can and made a shim for the trigger block/top hat seat.
Its pretty shocking that I could use a can and get complete wrap around. Slid in nicely has made it tight and centered. Threw in pic of the angled seal. The felt must have compressed somewhat and allowed it to sit to low. Pulled it out and got a Oring put it between 2 washers and compressed it in vice. Replaced the felt with it. Seal sits proud now so should seal much better. Think will finish putting back together tomorrow and do a few test shots with the air chief pellets before doing the gel thing. If that don't work the stock will be stuffed. Brought a couple bolts to replace the stock sight bolts so can drill out picatinny rail and mount dot sight to barrel. All fun and games. |
|
RangerPete
Senior Member Joined: 18 Apr 2023 Location: Cambridge. Status: Offline Posts: 879 |
Post Options
Thanks(0)
|
If those air chief pellets are the ones Iโm thinking of they are made by H&N.
Iโve tested them at 10m And they are good ๐๐ป Iโll actually test them at 20 tomorrow, seeing as I can now shoot 20m, under the boatโฆ ๐๐๐ |
|
Walk quietly, but carry a big stick.
|
|
kruzaroad
Senior Member Joined: 02 Jul 2022 Location: Hastings 4 now Status: Offline Posts: 2258 |
Post Options
Thanks(0)
|
Well don't see improvement.
Last group shot with air chief target. (bottom right unmarked is a exact heavy. flyer from worse group lower down.) This group 50mm x 30mm. This time I've got to take a lot more blame for spread. Had a horrible time with the rear blade blurring/turning into 4 dots for some reason. (older age I suspect) At this stage that's it till I can be bothered drilling picatinny rail to fit. Better get more accurate results before alter stock. But at moment I'm off to twack a Starling or mynar 2 with 1322. |
|
KiwiTR6
Senior Member Joined: 03 Nov 2022 Location: Stratford Status: Offline Posts: 269 |
Post Options
Thanks(0)
|
(Copied across from my pellet variance post as it's relevant to the discussion here). Started having a sort through the tin of 4.52 JSB 'Exacts' tonight
dividing them into 4.44 and under on one side and 4.46 and larger on the
other (the verniers are accurate to .02mm). I haven't made a lot of
progress as you can see but the ratio is about 2:1. The smallest is
4.42 and the largest 4.48 - a long way off the 4.52 stated on the tin
regardless. To further demonstrate my thinking
re the Air Chief challenge gun, a pic of a 4.42 JSB sitting nicely
inside the barrel and another of a 4.52 Sig that won't enter without
being forced in. To my way of thinking the 4.42 is going to shoot
straighter in this gun than the 4.52. |
|
FX Wildcat MK111 BT Sniper .25
FX Dreamline Classic .22 Diana Outlaw .22 Cometa Fenix 400 .177 Weihrauch HW50 .177 Crosman 2240 PCP Custom .22 Crosman 2250 PCP Custom .22 |
|
Post Reply | Page <1 2526272829 32> |
Tweet
|
Forum Jump | Forum Permissions You cannot post new topics in this forum You cannot reply to topics in this forum You cannot delete your posts in this forum You cannot edit your posts in this forum You cannot create polls in this forum You cannot vote in polls in this forum |