Kiwi Airgunners Forum : broken top sear www.kiwiairgunners.co.nz/ This is an XML content feed of; Kiwi Airgunners Forum : Pauly's Technical Area : broken top sear Copyright (c) 2006-2012 Web Wiz Forums - All Rights Reserved. Tue, 28 Apr 2026 06:55:45 +0000 Sun, 11 Dec 2016 15:24:34 +0000 http://blogs.law.harvard.edu/tech/rss Web Wiz Forums 10.14 360 www.kiwiairgunners.co.nz/RSS_post_feed.asp?TID=276 Kiwi Airgunners Forum www.kiwiairgunners.co.nz/forum_images/logo.jpg www.kiwiairgunners.co.nz/ broken top sear : Pauly5 wrote:Sounds like its... www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1658#1658 Author: Rabbiter
Subject: 276
Posted: 11 Dec 2016 at 3:24pm

Originally posted by Pauly5 Pauly5 wrote:

Sounds like its a tack driver. With doing repairs you get to know your gun well, and often get to tune them up a bit at the same time.
Photos of quarry is always good to see. Wink

Yes ,I'm thinking the same ,Id like to replace those sh*t trigger side plate screws with good allen key bolts .  ]]> Sun, 11 Dec 2016 15:24:34 +0000 www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1658#1658 broken top sear : Sounds like its a tack driver.... www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1655#1655 Author: Pauly5
Subject: 276
Posted: 11 Dec 2016 at 11:35am

Sounds like its a tack driver. With doing repairs you get to know your gun well, and often get to tune them up a bit at the same time.
Photos of quarry is always good to see. Wink
]]> Sun, 11 Dec 2016 11:35:49 +0000 www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1655#1655 broken top sear : I was gutted to be truthful &... www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1654#1654 Author: Rabbiter
Subject: 276
Posted: 11 Dec 2016 at 11:27am

I was gutted to be truthful & wasnt sure if Id done some major damage else where but its back on track ,placing touching holes at 55 yards on half a egg sized target ,good enough for most rabbits .I aim for the engine room ,the odd head shot but i aim is to "take as many of em out "get some lead into them & a finisher if needed .]]> Sun, 11 Dec 2016 11:27:25 +0000 www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1654#1654 broken top sear : Good to get that sorted. Dont... www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1653#1653 Author: Pauly5
Subject: 276
Posted: 11 Dec 2016 at 3:56am

Good to get that sorted. Dont want to be rough with that hottie.😋]]> Sun, 11 Dec 2016 03:56:25 +0000 www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1653#1653 broken top sear : I had a couple of feck ups the... www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1651#1651 Author: Rabbiter
Subject: 276
Posted: 10 Dec 2016 at 1:50am

I had a couple of feck ups the other niteCry ,due to a very busy period ,lack of sleep and hours of shooting ,mistakes come very easy,new gun and all .I wasnt sure if I would do real damage if I fired the S 510 without a pellet up the beech ,so at some stage due to all these factours after reloading I managed to load up a total of 2 pellets and even gave the third a bloody good go.lol Of course that shut the whole operation down & I  just went back to my bed !In the morning a .22 push rod saw the pellets out but it wouldnt cock so I regassed it and that did the trick however when I went to work the lever back my fat Southland fingers slipped half way back =after I took the side plate off I spotted a broke top sear .I gave Ron(bloody good bugger ) at Youngs air guns a ring and he sent me a couple down ,stating he had only fixed two in two years so I didnt need to order 5 spares ha ha .I also ordered a AAmag light which I use to check to see if I have already have a pellet loaded in the beech,tested it and it works well from muzzel end .While I had the trigger apart I decided to give all 3 sears a bit of a polish up ,now these babys are as smooth as a 22 year old hotties inner thighClap .Its all a learning curveWink but hopefully lessons have been learnt .]]> Sat, 10 Dec 2016 01:50:44 +0000 www.kiwiairgunners.co.nz/forum_posts.asp?TID=276&PID=1651#1651